This new Rode PSA1+ is covered by Rode's 1-year limited warranty from the date of purchase. Rode lists the PSA1+ as an accessory, and its accessory warranties cannot be extended by registration.
The Rode PSA1+ is a desk-mounted studio boom arm with a spring-balanced parallelogram design, 37 in (940 mm) of reach and a load range of 0.2 to 2.7 lb (94 g to 1.2 kg), built to hold a podcast, streaming or broadcast mic right where you talk and keep it off the desk.It clamps to a desk edge or bolts through a drilled hole, with both mounts in the box, and it turns a full 360 degrees. Fully damped springs inside a neoprene cover keep the arm quiet as you move it, and four clips along the top hold a USB or XLR cable. One number shapes every choice you make with it: the mic and everything mounted with it must weigh no more than 2.7 lb (1.2 kg) in total.
Rode PSA1+ at a glance
Load range
0.2 to 2.7 lb94 g to 1.2 kg
Reach
37 in out, 34 in up940 mm, 860 mm
Rotation
Full 360° swing
Desk mounts
Clamp or threaded insert, both included
Desk thickness
Clamp 2.75 in, insert 2.2 in70 mm clamp, 55 mm insert
Six features, from the spring balance to the two desk mounts
+
A boom arm has one job: hold the mic exactly where you put it, quietly, and get out of the way when you are done. The PSA1+ does that with a spring-balanced arm, a wide load window, and enough reach and swing to put the mic where you actually sit.
Tap a feature to exploreEach one opens to a beginner's guide, the pro details and real-world tips.
Spring-balanced arm
Parallelogram design
Aim holds as height changes
Spring-balanced arm
A parallelogram spring arm that keeps the mic aimed while you move it
The PSA1+ is a two-section parallelogram arm held in balance by internal springs. Linked bars in each section keep the mic pointing the same direction while you raise or lower it, so you set the angle once and only ever change the height. Rode promises stable support across the whole load range, as long as the base is fixed firmly to a desk or table.
Beginner's guide
What it is
Pairs of parallel bars linked at each joint. When the arm rises or drops, the bars move together, so the tip holds its angle.
Think of it like
An architect's lamp: pull it down to the page or push it out of the way, and the shade stays pointed where you left it.
Why you'll care
You aim the mic at your mouth once. After that, a nudge up or down changes only the height, not where the mic points.
Pro's guide
Springs in each section counter the weight on the tip. That is why the arm has a minimum as well as a maximum: too light and the arm can drift up, too heavy and it droops. Rode publishes no tension-adjustment procedure for the PSA1+, so plan to match the load to the 94 g to 1.2 kg window rather than to tune the springs.
Arm typeTwo-section parallelogram
Held byInternal spring tension
SpringsFully damped
Load range0.2 to 2.7 lb (94 g min, 1.2 kg max)
Real-world fit
Great for
Changing height oftenRaise or drop the mic without re-aiming it.
Sharing a deskPush the arm up and away when someone else sits down.
Pro tip: Set the mic angle first with the thumb knobs at the tip, then use the arm only for height and distance.
Quiet by design
Damped springs, neoprene cover
Less desk noise in the mic
Quiet by design
Damped springs and rubber contact points to keep desk noise out of the mic
Rode built the PSA1+ to be heard as little as possible. Its springs sit inside the arm, fully damped, under a neoprene cover, and the design goal is quiet operation. Rubber contact points add isolation from knocks, bumps and keyboard or mouse clicks. Rode publishes no measured isolation figure, so read this as the design intent: a quieter arm, not a substitute for good mic placement.
Beginner's guide
What it is
Damping slows and softens a spring's movement so it does not ring or rattle. Neoprene, the rubbery material used in wetsuits, wraps the arm.
Think of it like
A soft-close drawer next to one that slams: the same motion, far less noise.
Why you'll care
Adjusting the mic mid-show, or bumping the desk, is less likely to land in your recording as a thump or a squeak.
Pro's guide
Two noise paths are covered. Noise from the arm itself, springs and joints, is handled by the damped internal springs and the neoprene cover. Noise carried up from the desk, typing, clicks and knocks, is handled by the rubber contact points. No decibel figure is published for either. For a very sensitive condenser, a shock mount between the arm and the mic adds another layer.
SpringsInternal, fully damped
Arm coverNeoprene
Contact pointsRubber
Published isolation figureNone
Real-world fit
Matters most for
Live streams and gamingKeys and mouse clicks travel through the desk; the rubber contact points are Rode's fix.
Moving the mic while recordingDamped springs make an adjustment far less audible.
Matters less for
Noise in the room itselfAn arm cannot stop sound that travels through the air. Close mic placement does that.
Pro tip: Typing on the same desk? Mount the arm at the far end from your keyboard, so fewer taps travel straight into the base.
Long reach, full swing
37 in reach, 360°
Folds to 19.7 in
Long reach, full swing
37 inches of reach and a full 360-degree swing
Fully extended, the PSA1+ reaches 37 in (940 mm) out and 34 in (860 mm) up from its base, and the whole arm rotates a full 360 degrees. That is enough to clamp it out of the way on a desk edge and still bring the mic in close, then swing it clear when you need the space. Folded, it measures 19.7 in (500 mm) long.
Beginner's guide
What it is
Horizontal reach is how far out the arm holds the mic from its mount; vertical reach is how high it can lift it.
Why you'll care
The mount does not have to sit right in front of you. Put it where it fits, and the arm carries the mic to your chair.
Pro's guide
Rode lists the collapsed size as 2.6 × 19.7 × 7.1 in (65 × 500 × 180 mm, W × L × D) and the fully extended size as 2.6 × 37.0 × 3.9 in (65 × 940 × 100 mm). Against the original PSA1, horizontal reach grew from 820 to 940 mm and vertical reach from 840 to 860 mm.
Horizontal reach37 in (940 mm)
Vertical reach34 in (860 mm)
RotationFull 360°
Collapsed length19.7 in (500 mm)
Real-world fit
Great for
Crowded desksMount it off to one side and keep the space in front of you clear.
Getting the mic out of the shotSwing it away when you go on camera without it.
Pro tip: Before you clamp or drill, sit in your chair and measure from the planned mount point to your mouth. Stay comfortably inside 37 in, because a fully stretched arm leaves you no room to adjust.
Wide load window
0.2 to 2.7 lb
Light USB to heavy broadcast
Wide load window
Holds 0.2 to 2.7 lb, from light USB mics to heavy broadcast mics
Rode rates the PSA1+ to carry anywhere from 0.2 lb (94 g) up to 2.7 lb (1.2 kg) with any microphone or shock mount that uses a standard thread. The low end covers small USB mics; the high end covers heavy broadcast mics such as Rode's PodMic at 2.07 lb (937 g). Add up the mic, its mount or clip, and anything else riding on the tip, and keep that total inside the window.
Beginner's guide
What it is
Load range is the weight the springs are built to balance. Below the minimum or above the maximum, the arm can creep up or sink down instead of holding still.
Think of it like
A seesaw sized for a certain rider: too light and it bobs up, too heavy and it bottoms out.
Why you'll care
It is the one spec that decides whether a mic works on this arm. Look up your mic's weight before you buy.
Pro's guide
Rode's compatible list includes the PodMic, Procaster, Podcaster, Broadcaster, NT-USB, NT-USB Mini and NT1, and Rode publishes a weight for each. The rows show the heaviest few. Rode's PSM1 shock mount adds 0.86 lb (390 g), so a Procaster in a PSM1 lands inside the limit with little to spare. The PSA1+ page does not say whether the 1.2 kg includes the mount, so count it.
PodMic2.07 lb (937 g)
Procaster1.64 lb (745 g)
Podcaster1.44 lb (655 g)
Procaster in a PSM12.50 lb (1135 g)
Arm limit2.7 lb (1.2 kg)
Real-world fit
Fits
Rode PodMicThe heaviest mic on Rode's list, still under the limit.
Rode NT-USB Mini1.29 lb (585 g), a light USB mic Rode names for this arm.
Rode NT10.97 lb (440 g), plus whatever shock mount you pair with it.
Anything above 2.7 lb with its mountThe springs are not built for it. Choose a stand rated for the weight.
Pro tip: No scale handy? Find the weights on the maker's spec sheets for your mic and mount, add them, and leave a little headroom below 2.7 lb.
Built-in cable clips
Four clips, USB or XLR
Tidy, secure cable runs
Built-in cable clips
Four cable clips that hold a USB or XLR cable along the arm
The original PSA1 used Velcro wraps. The PSA1+ has integrated cable management instead: four clips along the top of the arm that you press the cable into, keeping it tidy and secure as the arm moves. No cable comes in the box, so plan on the one your mic needs: an XLR cable for an analog mic, or the USB cable a USB mic supplies.
Beginner's guide
What it is
XLR is the three-pin cable most pro mics use; USB connects a USB mic straight to a computer. The clips take either one.
Why you'll care
A loose cable hanging off the mic can swing, tug on the arm and catch on things. Clipped along the top, it travels with the arm.
Pro's guide
ClipsFour, along the top of the arm
Cable typesUSB or XLR
Cable includedNone
Real-world fit
You need
An XLR cable, for an XLR micOur 10 ft house cable is our standard match for a desk arm.
Nothing extra, for a USB micUse the USB cable that comes with the mic.
Pro tip: From the base, run the cable down the back of the desk, so it stays clear of your mouse hand and your feet.
Two desk mounts in the box
Clamp or threaded insert
Plus a 3/8 to 5/8 in adaptor
Two desk mounts in the box
Clamp it to the edge or bolt it through the desk, your choice
Both mounts come in the box. The padded desk clamp grips the edge of a table with a knob underneath; the threaded desk insert passes through a 2 to 3.1 in (50 to 80 mm) hole for a permanent, clean install. The clamp suits a desktop up to 2.75 in (70 mm) thick; the insert, up to 2.2 in (55 mm). At the tip, a 3/8 in thread, plus the 3/8 to 5/8 in adaptor from the box, takes standard mic clips and shock mounts, with the mic hanging or upright, end-address or side-address.
Beginner's guide
What it is
A desk clamp is a C-shaped grip that tightens onto the desk edge. A threaded insert is a bolt-through mount that needs a hole drilled in the desktop.
Think of it like
Renting versus owning: the clamp comes off in a minute, the insert stays put for good.
Why you'll care
Start with the clamp. If the mic spot works, you can switch to the insert later without buying anything else.
Pro's guide
The arm's plain end, the one without a screw thread, drops into either base. Rode's quick start guide calls for a 50 to 80 mm hole for the insert: the top baseplate's thread goes down through the hole, and the bottom plate is tightened from below with the supplied nut. Rode says the arm accepts any standard shock mount, and every Rode mic and shock mount except lavalier, mobile, wireless and headset mics and the SM5.
MountsDesk clamp and threaded insert
Desk clamp thicknessUp to 2.75 in (70 mm)
Insert desk thicknessUp to 2.2 in (55 mm)
Insert hole2 to 3.1 in diameter (50 to 80 mm)
Thread3/8 in, 3/8 to 5/8 in adaptor included
Real-world fit
Think twice if
Your desk is thicker than 2.2 inUse the clamp: Rode rates it for tops up to 2.75 in (70 mm), while the insert stops at 2.2 in (55 mm). Past 2.75 in, chat with us before you order.
You want it on a C-stand or floor standIt is designed to mount to a desk or table.
Pro tip: Fit the empty base first and seat the arm before the mic goes on, so you are never holding a heavy mic in one hand while you tighten a knob with the other.
Setup guide
How to set up the PSA1+
Five steps from the box to a mic in position, each with a pro tip+
From box to on-air in five steps
Every step comes with a pro tip from our audio team.Open all tips
Swipe through the steps→
1
Unbox and unfold
Take the arm and its parts out of the box and carefully extend the arm before you mount anything.
Pro tip
Lay the parts out first: arm, clamp, insert plates and nut, and the small 3/8 to 5/8 in adaptor, the easiest piece to misplace.
2
Mount the base
Clamp: set it on the desk edge and turn the knob underneath clockwise. Insert: drill a 2 to 3.1 in (50 to 80 mm) hole, drop the top plate's thread through it and tighten the bottom plate with the nut. Then drop the unthreaded end of the arm into the base.
Pro tip
Measure your desk before you start. Desk thicker than 2.2 in (55 mm)? Use the clamp, which Rode rates to 2.75 in (70 mm). The threaded insert is rated to 2.2 in (55 mm).
3
Attach the mic
Thread the mic, its clip or a shock mount onto the tip. If your mount needs 5/8 in, fit the adaptor first.
Pro tip
Check the total now, while it is easy to change: everything on the tip should come to between 0.2 and 2.7 lb (94 g and 1.2 kg).
4
Run the cable
Plug the cable into the mic and press it into the four clips along the top of the arm.
Pro tip
Leave a gentle loop of slack at the mic and at the elbow, so stretching the arm out never tugs on the connector.
5
Aim and set your distance
Lock the mic angle with the thumb knobs, then bring it to about 2 to 4 in (5 to 10 cm) from your mouth for speech, the distance Rode suggests.
Pro tip
Running the mic upright, on top of the arm? Give the thumb knobs an extra turn so the mic cannot slowly rotate.
A mic, a cable and an interface, all picked for this arm+
The PSA1+ arrives as an arm, two desk mounts and a thread adaptor. There is no mic, cable, clip or shock mount in the box. Here is the rest of an all-Rode desk chain, plus our own house cable.
1
Pick your use
Tap what you will use it for. We show how the PSA1+ fits and set up the gear below to match.
Up to 2.7 lb on the tip covers every broadcast mic on Rode's compatible list, up to the 2.07 lb (937 g) PodMic
Clamp or insert fixes the arm to the table, so the mic hangs in front of you instead of standing on the desk
Spring-balanced arm lets you lean in or sit back and bring the mic with you
Watch for: Weigh the whole rig before you buy. A mic, its mount and a clip-on pop filter all add up against the 2.7 lb (1.2 kg) ceiling.
The gear below is our desk podcast pick: Rode's PodMic, a 10 ft XLR cable, the AI-1 interface and NTH-100 headphones. See your gear ↓
Great fit
A great fit for streaming and gaming setups
Why it fits
Rubber contact points are Rode's answer to keyboard clicks, mouse taps and desk bumps reaching the mic
Four cable clips take a USB cable as easily as an XLR
Low 0.2 lb minimum lets light USB mics balance too, not just heavy broadcast models
Watch for: Rode suggests speaking from about 2 to 4 in (5 to 10 cm). That close, you can run less gain and leave game audio and keys in the background.
Our picks below assume an XLR mic. Streaming on a USB mic instead? Skip the cable and interface tiles, since the mic connects straight to the computer. See your gear ↓
Great fit
A great fit for voiceover and broadcast desks
Why it fits
Rode builds it for broadcasters, alongside podcasters, streamers and creators
Full 360° swing moves the mic aside between reads and brings it back for the next take
Parallelogram springs keep the mic aimed the same way as you raise or lower it
The gear below is what we would put on a voiceover desk: a dynamic mic, our 10 ft cable, the AI-1 and closed-back headphones. See your gear ↓
Good fit
A good fit for a large-diaphragm condenser, after a weight check
Why it fits
A 2.7 lb ceiling leaves room for many studio condensers; Rode lists its NT1 at 0.97 lb (440 g)
3/8 in thread and 5/8 in adaptor fit standard shock mounts, which Rode says the arm accepts
Watch for: Do the math first: condenser, shock mount and any filter clipped to the arm must total less than 2.7 lb (1.2 kg). Close to the line? Ask us before you order.
The AI-1 below supplies the 48 V a condenser needs. Bring your own mic if it fits the weight budget; we switched the pop filter to a clamp-on screen, since the WS14 is shaped for the PodMic. See your gear ↓
Not ideal
Not the right tool for heavy gear or for use away from a desk
Why it is not ideal
Built for a mic, within a hard limit: the springs top out at 2.7 lb (1.2 kg), and Rode states no load figures for anything but microphones and mounts
Made for a desk or table: Rode designs it to mount there, not on a floor stand, a C-stand or a stage
Watch for: For stage or floor use, a stand with its own base is the usual choice.
Send us what you want to mount and where, and we will find a stand or mount rated for it.
2
You'll need these to start recording
The arm holds the mic; it does not include one, or a cable, or anything to plug into. Already own a mic that weighs 0.2 to 2.7 lb with its mount? Skip that tile.
Swipe for all 3→
Microphone
Rode lists its PodMic as compatible, and at 2.07 lb (937 g) it is the heaviest mic on that list, still under the arm's limit.
An XLR mic like the PodMic plugs into an interface, not straight into the computer. Rode's AI-1 has one combo input with 48 V and a headphone jack, enough for one voice.
Rode built the WS14 foam cover for the PodMic and PodMic USB. At 34 g it barely dents the arm's limit. Black is our pick; seven other colors are available.
On-Stage's QK-2B adds a push-button release on top of the 5/8 in adaptor, so a 5/8 in mount comes off and goes back in one press. Count its weight toward the 2.7 lb limit.
Reach, load range, mounting and cables, side by side+
Two other Rode mic supports we carry. The original PSA1 is the earlier version of this arm; the DS2 is a desktop stand on a weighted base, for when you cannot clamp or drill.
Your mic and mount weigh 1.5 to 2.4 lb, the range it was built for
You cannot clamp to or drill your desk
Mounting
Desk clamp or threaded insert
Desk clamp or threaded insert
Weighted base, no clamp
Reach
37 in out, 34 in up Longest reach940 mm, 860 mm
32.3 in out, 33.1 in up820 mm, 840 mm
Up to 15 in tall380 mm
Load range
0.2 to 2.7 lb94 g to 1.2 kg
1.5 to 2.4 lb700 g to 1.1 kg
Up to 2.09 lb950 g
Movement
360° swing, parallelogram springs
360° swing, parallelogram springs
Two pivot points
Cable management
Four clips, USB or XLR
Velcro wraps
Cable guide slots
Mic thread
3/8 in, 5/8 in adaptor included
3/8 in, 5/8 in adaptor included
3/8 in, 1/4 in adaptor included
Weight
3.35 lb1.52 kg
3.84 lb1.74 kg
3.24 lbLightest1471 g
Specs from Rode's published data. Prices are live from our store.
Specs explained
What the PSA1+'s specs mean
Every arm spec on this page, in plain English+
Decode the spec sheet
New to boom arms? Here is what each spec means, with the PSA1+'s own number.Open all specs
Weight and reachLoad range · Horizontal reach · Vertical reach · Collapsed and extended size · Arm weight+
Load range
The total weight the springs are built to balance: the mic plus whatever mount, clip or filter rides on the tip. The PSA1+ is rated for 0.2 to 2.7 lb (94 g to 1.2 kg).
Horizontal reach
How far out from its mount the arm can hold a mic. The PSA1+ stretches to 37 in (940 mm).
Vertical reach
How high above its mount the arm can lift a mic. On the PSA1+ that is 34 in (860 mm).
Collapsed and extended size
The arm folded up versus stretched out: 19.7 in (500 mm) long folded, 37 in (940 mm) extended.
Arm weight
What the arm itself weighs, separate from what it can hold. The PSA1+ weighs 3.35 lb (1.52 kg).
Movement and noiseParallelogram arm · Damped springs · 360-degree rotation+
Parallelogram arm
Paired parallel bars in each section that keep the tip at a fixed angle as the arm moves. Aim the mic once and height changes leave it alone.
Damped springs
Springs whose movement is softened so they do not ring or rattle. The PSA1+ keeps fully damped springs inside the arm, under a neoprene cover.
360-degree rotation
The arm turns all the way around its base, so it can work from your left, your right or swing behind you.
MountingDesk clamp · Threaded desk insert · Thread size · Shock mount · End-address and side-address+
Desk clamp
A C-shaped grip that tightens onto the edge of a desk or table, with no drilling. Rode rates the PSA1+ clamp for desks up to 2.75 in (70 mm) thick.
Threaded desk insert
A bolt-through mount: a threaded top plate drops through a 2 to 3.1 in (50 to 80 mm) hole and a nut locks the bottom plate underneath. Neater and more permanent than a clamp. Rode rates the PSA1+ insert for desks up to 2.2 in (55 mm) thick.
Thread size
The screw size where the mic attaches. The PSA1+ has a 3/8 in thread, and the included adaptor converts it to 5/8 in for clips and shock mounts that need it.
Shock mount
An elastic suspension that floats the mic so bumps do not reach it. None comes with the arm; Rode says any standard shock mount fits.
End-address and side-address
Whether you speak into the tip of a mic or into its side. The PSA1+ holds either type, hanging down or sitting upright.
CablesXLR and USB+
XLR and USB
XLR is the three-pin analog cable pro mics use, usually run to an interface or mixer. USB carries a USB mic's signal straight to a computer. The four clips on the PSA1+ take either.
FAQ & Contact Us
Questions about the Rode PSA1+?
More questions shoppers ask: weight, compatibility, the original PSA1, mounting and mic position.
+
How much weight can the PSA1+ hold?+
Between 0.2 and 2.7 lb (94 g and 1.2 kg), per Rode. That figure should cover your mic together with its shock mount or clip and anything else attached at the tip, so the springs can balance the load.
Does the PSA1+ only work with Rode mics?+
No. Rode says it takes any microphone or shock mount with a standard thread in that weight range. The exceptions Rode lists are lavalier, mobile, wireless and headset mics, plus its own SM5 shock mount.
How is the PSA1+ different from the original PSA1?+
It reaches farther, 37 in out instead of 32.3 in (940 vs 820 mm). It holds lighter mics, down to 0.2 lb (94 g) instead of 1.5 lb (700 g), and slightly heavier ones, 2.7 lb instead of 2.4 lb. It weighs less, 3.35 lb versus 3.84 lb, and it trades the old Velcro wraps for four built-in clips. See both in Compare.
Should I use the clamp or drill a hole for the insert?+
Either works, and both are in the box. The clamp grips a desk edge with no tools; the threaded insert needs a 2 to 3.1 in (50 to 80 mm) hole. Rode's datasheet lists the clamp at 70 mm and the insert at 55 mm, so a thicker desk points you to the clamp. Check your desk edge before you buy, and chat with our team if it is close to the limit.
Can I mount the mic upright instead of hanging down?+
Yes. The PSA1+ holds a mic hanging below the arm or sitting on top, end-address or side-address. In the upright position, Rode says to tighten the thumb knobs further so the mic does not turn by itself.
Will the PSA1+ hold a RODECaster console?+
Not the RODECaster Pro 2 or the RODECaster Video. By Rode's own weights they come in at 4.32 lb (1960 g) and 2.77 lb (1257 g), both over the arm's 2.7 lb (1.2 kg) limit, and Rode makes no load claim for consoles on this arm. It is designed to hold a microphone.